$ EZ-EDS Version 3.0 Generated Electronic Data Sheet [File] DescText = "EX12#-SCM#"; CreateDate = 08-28-2008; CreateTime = 10:31:07; ModDate = 08-28-2008; ModTime = 14:18:51; Revision = 1.0; [Device] VendCode = 7; VendName = "SMC Corporation"; ProdType = 27; ProdTypeStr = "Pneumatic Valve(s)"; ProdCode = 128; MajRev = 1; MinRev = 1; ProdName = "EX12#-SCM#"; [Device Classification] Class1 = CompoNet; [CompoNet_Device] Device_Category = 2; [CompoNet_IO] CompoNet_Output_Info = 0, 16; $==================================Parameter=============================================== [ParamClass] MaxInst =141; $ Number of Parameters Descriptor =6; $ Characteristics of Parameter $ (Supports Full Attribute,Must do non-volatile storage save command) CfgAssembly =0; $ Not support Configuration Assembly [Params] $========================= $== UNIT MANAGER OBJECT == $========================= $ Generic Status Param1= 0, $shall Equal 0 6, $path size "20 95 24 01 30 65", $path 0x0030, $descriptor 0xD1, $data type=BYTE 1, $data size=1byte "Generic Status", $name "", $unit "bit0:I/O power status bit of terminal 1\n" "bit1:I/O power status bit of terminal 2\n" "bit2:Network power voltage drops ( below the set level )\n" "bit3:Unit maintenance bit\n" "bit4:Reserved\n" "bit5:Reserved\n" "bit6:Operation time over bit\n" "bit7:Connected component maintenance bit", $Help string 0x00,0xff,0x00, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ NETWORK POWER VOLTAGE Param2= 0, $shall Equal 0 6, $path size "20 95 24 01 30 6B", $path 0x0030, $descriptor 0xC7, $data type=UINT(2byte) 2, $data size=2byte "Network Power Voltage Monitor", $name "V", $unit "Shows the present value of the network power voltage.", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ MAX NETWORK POWER VOLTAGE Param3= 0, $shall Equal 0 6, $path size "20 95 24 01 30 6C", $path 0x0030, $descriptor 0xC7, $data type=UINT(2byte) 2, $data size=2byte "Network Power Voltage (Peak)", $name "V", $unit "Shows the peak value of the network power voltage.", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ MIN NETWORK POWER VOLTAGE Param4= 0, $shall Equal 0 6, $path size "20 95 24 01 30 6D", $path 0x0030, $descriptor 0xC7, $data type=UINT(2byte) 2, $data size=2byte "Network Power Voltage (Bottom)", $name "V", $unit "Shows the bottom value of the network power voltage.", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ THRESHOLD NETWORK POWER VOLTAGE Param5= 0, $shall Equal 0 6, $path size "20 95 24 01 30 6E", $path 0x0000, $descriptor 0xC7, $data type=UINT(2byte) 2, $data size=2byte "Network Power Voltage", $name "V", $unit "Sets the threshold of the network power voltage.", $Help string 80,300,110, $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS Param6= 0, $shall Equal 0 6, $path size "20 95 24 01 30 71", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Unit Conduction Time Monitor", $name "Hour", $unit "Shows the present value of the unit conduction time.", $Help string 0,0xffffffff,0, $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS EXCEED Param7= 0, $shall Equal 0 6, $path size "20 95 24 01 30 72", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Unit Conduction Time Detection", $name "", $unit "When the unit conduction time is detected,\n" "this data changes and bit3 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD RUN HOURS Param8= 0, $shall Equal 0 6, $path size "20 95 24 01 30 73", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Unit Conduction Time", $name "Hour", $unit "Sets the threshold of the unit conduction time.", $Help string 0,0xffffffff,0, $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $==================================== $== COMMUNICATION ERROR LOG OBJECT == $==================================== $ ERROR CODE (1) Param9= 0, $shall Equal 0 6, $path size "20 96 24 04 30 64", $path 0x0012, $descriptor 0xC6, $data type=USINT 1, $data size=1byte "Communication Error Code [1]", $name "", $unit "This is the error classification code when communication error occurrs.\n" "[1] = latest", $Help string 0,3,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ NETWORK POWER VOLTAGE (1) Param10= 0, $shall Equal 0 6, $path size "20 96 24 04 30 67", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Fault Network Power Voltage [1]", $name "V", $unit "This is the network power voltage when communication error occurrs.\n" "[1] = latest", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS (1) Param11= 0, 6, "20 96 24 04 30 68", 0x0010, 0xC8, 4, "Unit Conduction Time Stamp [1]", "Hour", "This is the unit conduction time when communication error occurrs,\n" "[1] = latest", ,,, 1,10,1,0, 0,0,0,0, 1; $ ERROR CODE (2) Param12= 0, $shall Equal 0 6, $path size "20 96 24 03 30 64", $path 0x0012, $descriptor 0xC6, $data type=USINT 1, $data size=1byte "Communication Error Code [2]", $name "", $unit "This is the error classification code when communication error occurrs.\n" "[2] = 2nd latest", $Help string 0,3,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ NETWORK POWER VOLTAGE (2) Param13= 0, $shall Equal 0 6, $path size "20 96 24 03 30 67", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Fault Network Power Voltage [2]", $name "V", $unit "This is the network power voltage when communication error occurrs.\n" "[2] = 2nd latest", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS (2) Param14= 0, 6, "20 96 24 03 30 68", 0x0010, 0xC8, 4, "Unit Conduction Time Stamp [2]", "Hour", "This is the unit conduction time when communication error occurrs,\n" "[2] = 2nd latest", ,,, 1,10,1,0, 0,0,0,0, 1; $ ERROR CODE (3) Param15= 0, $shall Equal 0 6, $path size "20 96 24 02 30 64", $path 0x0012, $descriptor 0xC6, $data type=USINT 1, $data size=1byte "Communication Error Code [3]", $name "", $unit "This is the error classification code when communication error occurrs.\n" "[3] = 3rd latest", $Help string 0,3,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ NETWORK POWER VOLTAGE (3) Param16= 0, $shall Equal 0 6, $path size "20 96 24 02 30 67", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Fault Network Power Voltage [3]", $name "V", $unit "This is the network power voltage when communication error occurrs.\n" "[3] = 3rd latest", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS (3) Param17= 0, 6, "20 96 24 02 30 68", 0x0010, 0xC8, 4, "Unit Conduction Time Stamp [3]", "Hour", "This is the unit conduction time when communication error occurrs,\n" "[3] = 3rd latest", ,,, 1,10,1,0, 0,0,0,0, 1; $ ERROR CODE (4) Param18= 0, $shall Equal 0 6, $path size "20 96 24 01 30 64", $path 0x0012, $descriptor 0xC6, $data type=USINT 1, $data size=1byte "Communication Error Code [4]", $name "", $unit "This is the error classification code when communication error occurrs.\n" "[4] = 4th latest", $Help string 0,3,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ NETWORK POWER VOLTAGE (4) Param19= 0, $shall Equal 0 6, $path size "20 96 24 01 30 67", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Fault Network Power Voltage [4]", $name "V", $unit "This is the network power voltage when communication error occurrs.\n" "[4] = 4th latest", $Help string , , , $min/ max/ default 1,10,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 1; $decimal places $ RUN HOURS (4) Param20= 0, 6, "20 96 24 01 30 68", 0x0010, 0xC8, 4, "Unit Conduction Time Stamp [4]", "Hour", "This is the unit conduction time when communication error occurrs,\n" "[4] = 4th latest", ,,, 1,10,1,0, 0,0,0,0, 1; $============================== $== EQUIPMENT MANAGER OBJECT == $============================== $ RESPONSE TIME (0) Param21= 0, $shall Equal 0 6, $path size "20 97 24 01 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [00]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:00 turns on till the time OUT:16 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (0) Param22= 0, $shall Equal 0 6, $path size "20 97 24 01 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [00]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (0) Param23= 0, $shall Equal 0 6, $path size "20 97 24 01 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [00]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:00 turns on till the time OUT:16 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (1) Param24= 0, $shall Equal 0 6, $path size "20 97 24 02 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [01]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:01 turns on till the time OUT:17 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (1) Param25= 0, $shall Equal 0 6, $path size "20 97 24 02 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [01]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (1) Param26= 0, $shall Equal 0 6, $path size "20 97 24 02 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [01]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:01 turns on till the time OUT:17 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (2) Param27= 0, $shall Equal 0 6, $path size "20 97 24 03 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [02]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:02 turns on till the time OUT:18 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (2) Param28= 0, $shall Equal 0 6, $path size "20 97 24 03 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [02]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (2) Param29= 0, $shall Equal 0 6, $path size "20 97 24 03 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [02]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:02 turns on till the time OUT:18 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (3) Param30= 0, $shall Equal 0 6, $path size "20 97 24 04 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [03]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:03 turns on till the time OUT:19 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (3) Param31= 0, $shall Equal 0 6, $path size "20 97 24 04 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [03]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (3) Param32= 0, $shall Equal 0 6, $path size "20 97 24 04 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [03]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:03 turns on till the time OUT:19 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (4) Param33= 0, $shall Equal 0 6, $path size "20 97 24 05 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [04]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:04 turns on till the time OUT:20 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (4) Param34= 0, $shall Equal 0 6, $path size "20 97 24 05 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [04]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (4) Param35= 0, $shall Equal 0 6, $path size "20 97 24 05 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [04]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:04 turns on till the time OUT:20 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (5) Param36= 0, $shall Equal 0 6, $path size "20 97 24 06 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [05]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:05 turns on till the time OUT:21 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (5) Param37= 0, $shall Equal 0 6, $path size "20 97 24 06 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [05]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (5) Param38= 0, $shall Equal 0 6, $path size "20 97 24 06 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [05]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:05 turns on till the time OUT:21 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (6) Param39= 0, $shall Equal 0 6, $path size "20 97 24 07 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [06]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:06 turns on till the time OUT:22 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (6) Param40= 0, $shall Equal 0 6, $path size "20 97 24 07 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [06]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (6) Param41= 0, $shall Equal 0 6, $path size "20 97 24 07 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [06]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:06 turns on till the time OUT:22 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $=== $ RESPONSE TIME (7) Param42= 0, $shall Equal 0 6, $path size "20 97 24 08 30 65", $path 0x0010, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time Monitor [07]", $name "ms", $unit "Shows the present value of the operation time, \n" "from the time OUT:07 turns on till the time OUT:23 turns on.", $Help string 0,0xffff,0000, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ RESPONSE TIME EXCEED (7) Param43= 0, $shall Equal 0 6, $path size "20 97 24 08 30 66", $path 0x0012, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Operation Time Detection [07]", $name "", $unit "When the operation time over is detected,\n" "this data changes and bit6 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $--- $ THRESHOLD RESPONSE TIME (7) Param44= 0, $shall Equal 0 6, $path size "20 97 24 08 30 67", $path 0x0000, $descriptor 0xC7, $data type=UINT 2, $data size=2byte "Operation Time [07]", $name "ms", $unit "Sets the threshold of the operation time,\n" "from the time OUT:07 turns on till the time OUT:23 turns on.", $Help string 0,0xffff,, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $================================== $== DISCRETE OUTPUT POINT OBJECT == $================================== $ FAULT ACTION (0) Param45= 0, $shall Equal 0 6, $path size "20 09 24 01 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [00]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (0) Param46= 0, $shall Equal 0 6, $path size "20 09 24 01 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [00]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (0) Param47= 0, $shall Equal 0 6, $path size "20 09 24 01 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [00]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (0) Param48= 0, $shall Equal 0 6, $path size "20 09 24 01 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [00]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (0) Param49= 0, $shall Equal 0 6, $path size "20 09 24 01 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [00]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (0) Param50= 0, $shall Equal 0 6, $path size "20 09 24 01 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [00]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (1) Param51= 0, $shall Equal 0 6, $path size "20 09 24 02 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [01]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (1) Param52= 0, $shall Equal 0 6, $path size "20 09 24 02 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [01]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (1) Param53= 0, $shall Equal 0 6, $path size "20 09 24 02 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [01]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (1) Param54= 0, $shall Equal 0 6, $path size "20 09 24 02 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [01]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (1) Param55= 0, $shall Equal 0 6, $path size "20 09 24 02 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [01]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (1) Param56= 0, $shall Equal 0 6, $path size "20 09 24 02 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [01]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (2) Param57= 0, $shall Equal 0 6, $path size "20 09 24 03 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [02]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (2) Param58= 0, $shall Equal 0 6, $path size "20 09 24 03 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [02]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (2) Param59= 0, $shall Equal 0 6, $path size "20 09 24 03 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [02]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (2) Param60= 0, $shall Equal 0 6, $path size "20 09 24 03 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [02]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (2) Param61= 0, $shall Equal 0 6, $path size "20 09 24 03 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [02]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (2) Param62= 0, $shall Equal 0 6, $path size "20 09 24 03 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [02]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (3) Param63= 0, $shall Equal 0 6, $path size "20 09 24 04 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [03]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (3) Param64= 0, $shall Equal 0 6, $path size "20 09 24 04 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [03]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (3) Param65= 0, $shall Equal 0 6, $path size "20 09 24 04 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [03]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (3) Param66= 0, $shall Equal 0 6, $path size "20 09 24 04 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [03]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (3) Param67= 0, $shall Equal 0 6, $path size "20 09 24 04 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [03]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (3) Param68= 0, $shall Equal 0 6, $path size "20 09 24 04 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [03]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (4) Param69= 0, $shall Equal 0 6, $path size "20 09 24 05 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [04]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (4) Param70= 0, $shall Equal 0 6, $path size "20 09 24 05 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [04]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (4) Param71= 0, $shall Equal 0 6, $path size "20 09 24 05 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [04]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (4) Param72= 0, $shall Equal 0 6, $path size "20 09 24 05 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [04]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (4) Param73= 0, $shall Equal 0 6, $path size "20 09 24 05 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [04]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (4) Param74= 0, $shall Equal 0 6, $path size "20 09 24 05 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [04]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (5) Param75= 0, $shall Equal 0 6, $path size "20 09 24 06 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [05]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (5) Param76= 0, $shall Equal 0 6, $path size "20 09 24 06 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [05]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (5) Param77= 0, $shall Equal 0 6, $path size "20 09 24 06 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [05]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (5) Param78= 0, $shall Equal 0 6, $path size "20 09 24 06 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [05]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (5) Param79= 0, $shall Equal 0 6, $path size "20 09 24 06 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [05]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (5) Param80= 0, $shall Equal 0 6, $path size "20 09 24 06 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [05]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (6) Param81= 0, $shall Equal 0 6, $path size "20 09 24 07 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [06]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (6) Param82= 0, $shall Equal 0 6, $path size "20 09 24 07 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [06]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (6) Param83= 0, $shall Equal 0 6, $path size "20 09 24 07 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [06]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (6) Param84= 0, $shall Equal 0 6, $path size "20 09 24 07 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [06]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (6) Param85= 0, $shall Equal 0 6, $path size "20 09 24 07 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [06]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (6) Param86= 0, $shall Equal 0 6, $path size "20 09 24 07 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [06]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (7) Param87= 0, $shall Equal 0 6, $path size "20 09 24 08 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [07]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (7) Param88= 0, $shall Equal 0 6, $path size "20 09 24 08 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [07]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (7) Param89= 0, $shall Equal 0 6, $path size "20 09 24 08 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [07]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (7) Param90= 0, $shall Equal 0 6, $path size "20 09 24 08 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [07]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (7) Param91= 0, $shall Equal 0 6, $path size "20 09 24 08 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [07]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (7) Param92= 0, $shall Equal 0 6, $path size "20 09 24 08 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [07]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (8) Param93= 0, $shall Equal 0 6, $path size "20 09 24 09 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [08]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (8) Param94= 0, $shall Equal 0 6, $path size "20 09 24 09 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [08]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (8) Param95= 0, $shall Equal 0 6, $path size "20 09 24 09 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [08]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (8) Param96= 0, $shall Equal 0 6, $path size "20 09 24 09 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [08]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (8) Param97= 0, $shall Equal 0 6, $path size "20 09 24 09 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [08]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (8) Param98= 0, $shall Equal 0 6, $path size "20 09 24 09 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [08]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (9) Param99= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [09]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (9) Param100= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [09]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (9) Param101= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [09]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (9) Param102= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [09]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (9) Param103= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [09]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (9) Param104= 0, $shall Equal 0 6, $path size "20 09 24 0A 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [09]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (10) Param105= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [10]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (10) Param106= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [10]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (10) Param107= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [10]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (10) Param108= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [10]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (10) Param109= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [10]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (10) Param110= 0, $shall Equal 0 6, $path size "20 09 24 0B 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [10]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (11) Param111= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [11]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (11) Param112= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [11]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (11) Param113= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [11]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (11) Param114= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [11]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (11) Param115= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [11]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (11) Param116= 0, $shall Equal 0 6, $path size "20 09 24 0C 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [11]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (12) Param117= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [12]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (12) Param118= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [12]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (12) Param119= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [12]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (12) Param120= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [12]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (12) Param121= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [12]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (12) Param122= 0, $shall Equal 0 6, $path size "20 09 24 0D 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [12]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (13) Param123= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [13]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (13) Param124= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [13]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (13) Param125= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [13]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (13) Param126= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [13]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (13) Param127= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [13]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (13) Param128= 0, $shall Equal 0 6, $path size "20 09 24 0E 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [13]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (14) Param129= 0, $shall Equal 0 6, $path size "20 09 24 0F 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [14]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (14) Param130= 0, $shall Equal 0 6, $path size "20 09 24 0f 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [14]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (14) Param131= 0, $shall Equal 0 6, $path size "20 09 24 0F 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [14]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (14) Param132= 0, $shall Equal 0 6, $path size "20 09 24 0F 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [14]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (14) Param133= 0, $shall Equal 0 6, $path size "20 09 24 0F 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [14]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (14) Param134= 0, $shall Equal 0 6, $path size "20 09 24 0F 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [14]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ FAULT ACTION (15) Param135= 0, $shall Equal 0 6, $path size "20 09 24 10 30 05", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Fault Action [15]", $name "", $unit "Sets the output states when communication error occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ IDLE ACTION (15) Param136= 0, $shall Equal 0 6, $path size "20 09 24 10 30 07", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Idle Action [15]", $name "", $unit "Sets the output states when idle state occurrs.\n" "[Clear Data] or [Hold Last Data]", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER MODE CHOICE (15) Param137= 0, $shall Equal 0 6, $path size "20 09 24 10 30 65", $path 0x0002, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "Detection Mode [15]", $name "", $unit "Changes the detection mode of connected components.\n" "After setteing, present value of the maintenance counter becomes zero.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER (15) Param138= 0, $shall Equal 0 6, $path size "20 09 24 10 30 66", $path 0x0030, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Count Monitor [15]", $name "second/count", $unit "Shows the present value of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ MAINTENANCE COUNTER EXCEED (15) Param139= 0, $shall Equal 0 6, $path size "20 09 24 10 30 67", $path 0x0012, $descriptor 0xC1, $data type=BOLL 1, $data size=1byte "Detection Status [15]", $name "", $unit "When the maintenance counter of connected components is detected,\n" "this data changes and bit7 of generic status turns on.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $ THRESHOLD MAINTENANCE COUNTER (15) Param140= 0, $shall Equal 0 6, $path size "20 09 24 10 30 68", $path 0x0000, $descriptor 0xC8, $data type=UDINT 4, $data size=4byte "Maintenance Counter [15]", $name "second/count", $unit "Sets the threshold of the maintenance counter of connected components.\n" "Total ON Time Monitor Mode:1 = 1 second\n" "Contact Operation Counter Mode:1 = 1 count", $Help string 0,0xffffffff,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $================================== $== DISCRETE OUTPUT GROUP OBJECT == $================================== $ STATUS Param141= 0, $shall Equal 0 6, $path size "20 1E 24 01 30 05", $path 0x0032, $descriptor 0xC1, $data type=BOOL 1, $data size=1byte "State of the Output Power Supply", $name "", $unit "Shows the state of the output power supply.", $Help string 0,1,0, $min/ max/ default 1,1,1,0, $mult/ div /base/ offset scaling 0,0,0,0, $mult/ div /base/ offset links not used 0; $decimal places $================================== Enum ================================================= [EnumPar] Param7= $ Unit Conduction Time Detection "OK", "Over the Threshold"; Param9= $ Communication Error Code [1] "No Error", "Connection Time Out", "Bus Off", "MAC ID Duplication"; Param12= $ Communication Error Code [2] "No Error", "Connection Time Out", "Bus Off", "MAC ID Duplication"; Param15= $ Communication Error Code [3] "No Error", "Connection Time Out", "Bus Off", "MAC ID Duplication"; Param18= $ Communication Error Code [4] "No Error", "Connection Time Out", "Bus Off", "MAC ID Duplication"; Param22= $ operation time detection [00] "OK", "Over the Threshold"; Param25= $ operation time detection [01] "OK", "Over the Threshold"; Param28= $ operation time detection [02] "OK", "Over the Threshold"; Param31= $ operation time detection [03] "OK", "Over the Threshold"; Param34= $ operation time detection [04] "OK", "Over the Threshold"; Param37= $ operation time detection [05] "OK", "Over the Threshold"; Param40= $ operation time detection [06] "OK", "Over the Threshold"; Param43= $ operation time detection [07] "OK", "Over the Threshold"; Param45= $ Fault Action [00] "Clear Data", "Hold Last State"; Param46= $ IDLE ACTION [00] "Clear Data", "Hold Last State"; Param47= $ Detection Mode [00] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param49= $ Detection Status [00] "OK", "Over the Threshold"; Param51= $ Fault Action [01] "Clear Data", "Hold Last State"; Param52= $ IDLE ACTION [01] "Clear Data", "Hold Last State"; Param53= $ Detection Mode [01] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param55= $ Detection Status [01] "OK", "Over the Threshold"; Param57= $ Fault Action [02] "Clear Data", "Hold Last State"; Param58= $ IDLE ACTION [02] "Clear Data", "Hold Last State"; Param59= $ Detection Mode [02] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param61= $ Detection Status [02] "OK", "Over the Threshold"; Param63= $ Fault Action [03] "Clear Data", "Hold Last State"; Param64= $ IDLE ACTION [03] "Clear Data", "Hold Last State"; Param65= $ Detection Mode [03] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param67= $ Detection Status [03] "OK", "Over the Threshold"; Param69= $ Fault Action [04] "Clear Data", "Hold Last State"; Param70= $ IDLE ACTION [04] "Clear Data", "Hold Last State"; Param71= $ Detection Mode [04] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param73= $ Detection Status [04] "OK", "Over the Threshold"; Param75= $ Fault Action [05] "Clear Data", "Hold Last State"; Param76= $ IDLE ACTION [05] "Clear Data", "Hold Last State"; Param77= $ Detection Mode [05] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param79= $ Detection Status [05] "OK", "Over the Threshold"; Param81= $ Fault Action [06] "Clear Data", "Hold Last State"; Param82= $ IDLE ACTION [06] "Clear Data", "Hold Last State"; Param83= $ Detection Mode [06] "Total ON Time Monitor Mode", "Contace Operation Count Mode"; Param85= $ Detection Status [06] "OK", "Over the Threshold"; Param87= $ Fault Action [07] "Clear Data", "Hold Last State"; Param88= $ IDLE ACTION [07] "Clear Data", "Hold Last State"; Param89= $ Detection Mode [07] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param91= $ Detection Status [07] "OK", "Over the Threshold"; Param93= $ Fault Action [08] "Clear Data", "Hold Last State"; Param94= $ IDLE ACTION [08] "Clear Data", "Hold Last State"; Param95= $ Detection Mode [08] "Total ON Time Monitor Mode", "Contact Operation Counert Mode"; Param97= $ Detection Status [08] "OK", "Over the Threshold"; Param99= $ Fault Action [09] "Clear Data", "Hold Last State"; Param100= $ IDLE ACTION [09] "Clear Data", "Hold Last State"; Param101= $ Detection Mode [09] "Total ON Time Monitor Mode", "Contace Operation Counter Mode"; Param103= $ Detection Status [09] "OK", "Over the Threshold"; Param105= $ Fault Action [10] "Clear Data", "Hold Last State"; Param106= $ IDLE ACTION [10] "Clear Data", "Hold Last State"; Param107= $ Detection Mode [10] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param109= $ Detection Status [10] "OK", "Over the Threshold"; Param111= $ Fault Action [11] "Clear Data", "Hold Last State"; Param112= $ IDLE ACTION [11] "Clear Data", "Hold Last State"; Param113= $ Detection Mode [11] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param115= $ Detection Status [11] "OK", "Over the Threshold"; Param117= $ Fault Action [12] "Clear Data", "Hold Last State"; Param118= $ IDLE ACTION [12] "Clear Data", "Hold Last State"; Param119= $ Detection Mode [12] "Total ON Time Monitor Mode", "Contace Operation Counter Mode"; Param121= $ Detection Status [12] "OK", "Over the Threshold"; Param123= $ Fault Action [13] "Clear Data", "Hold Last State"; Param124= $ IDLE ACTION [13] "Clear Data", "Hold Last State"; Param125= $ Detection Mode [13] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param127= $ Detection Status [13] "OK", "Over the Threshold"; Param129= $ Fault Action [14] "Clear Data", "Hold Last State"; Param130= $ IDLE ACTION [14] "Clear Data", "Hold Last State"; Param131= $ Detection Mode [14] "Total ON Time Monitor Mode", "Contact Operation Counter Mode"; Param133= $ Detection Status [14] "OK", "Over the Threshold"; Param135= $ Fault Action [15] "Clear Data", "Hold Last State"; Param136= $ Fault Action [15] "Clear Data", "Hold Last State"; Param137= $ Detection Mode [15] "Total ON Time Monitor Mode", "Contace Operation Counter Mode"; Param139= $ Detection Status [15] "OK", "Over the Threshold"; Param141= $ The State of the Output Power Supply "Output Power ON", "Output Power OFF"; [Groups] Group1="General Setting", 4, 2,5,6,8; Group2="Output Point Setting", 64, 45,46,47,50,51,52,53,56, 57,58,59,62,63,64,65,68, 69,70,71,74,75,76,77,80, 81,82,83,86,87,88,89,92, 93,94,95,98,99,100,101,104, 105,106,107,110,111,112,113,116, 117,118,119,122,123,124,125,128, 129,130,131,134,135,136,137,140; Group3="Operation Time Setting", 8, 23,26,29,32,35,38,41,44; Group4="Detection Mode Setting", 16, 47,53,59,65,71,77,83,89, 95,101,107,113,119,125,131,137; Group5="Maintenance Counter Setting", 16, 50,56,62,68,74,80,86,92, 98,104,110,116,122,128,134,140; Group6="Fault Action Setting", 16, 45,51,57,63,69,75,81,87, 93,99,105,111,117,123,129,135; Group7="Idle Action Setting", 16, 46,52,58,64,70,76,82,88, 94,100,106,112,118,124,130,136; Group8="General Monitor", 7, 1,2,3,4,6,7,141; Group9="Output Point Monitor ", 32, 48,49,54,55,60,61,66,67, 72,73,78,79,84,85,90,91, 96,97,102,103,108,109,114,115, 120,121,126,127,132,133,138,139; Group10="Operation Time Monitor", 16, 21,22,24,25,27,28,30,31, 33,34,36,37,39,40,42,43; Group11="Communication Error History", 12, 9,10,11,12,13,14,15,16, 17,18,19,20; Group12="Output Point [00] Information", 6, 45,46,47,48,49,50; Group13="Output Point [01] Information", 6, 51,52,53,54,55,56; Group14="Output Point [02] Information", 6, 57,58,59,60,61,62; Group15="Output Point [03] Information", 6, 63,64,65,66,67,68; Group16="Output Point [04] Information", 6, 69,70,71,72,73,74; Group17="Output Point [05] Information", 6, 75,76,77,78,79,80; Group18="Output Point [06] Information", 6, 81,82,83,84,85,86; Group19="Output Point [07] Information", 6, 87,88,89,90,91,92; Group20="Output Point [08] Information", 6, 93,94,95,96,97,98; Group21="Output Point [09] Information", 6, 99,100,101,102,103,104; Group22="Output Point [10] Information", 6, 105,106,107,108,109,110; Group23="Output Point [11] Information", 6, 111,112,113,114,115,116; Group24="Output Point [12] Information", 6, 117,118,119,120,121,122; Group25="Output Point [13] Information", 6, 123,124,125,126,127,128; Group26="Output Point [14] Information", 6, 129,130,131,132,133,134; Group27="Output Point [15] Information", 6, 135,136,137,138,139,140;